The Art of Basic Plumbing for Installing a Bathtub
The Art of Basic Plumbing for Installing a Bathtub
Blog Article
On this page below you will find a good deal of reliable content in regards to Installing A Bathtub.
Installing a bath tub isn't exactly rocket science, yet it does call for strong plumbing, carpentry, and also occasionally, tiling skills. Changing an old bathtub with a brand-new one is likewise a reasonably challenging project. If the old bathtub is readily easily accessible, the job can relocate easily; if you have to open up a wall to eliminate the old tub and also place the new tub, the job is much harder. In either case, the job is within a residence handyman's skills, although you will require a helper to vacate the old bathtub and also embeded in the new one. Make sure you have certified on your own for the job and also fit attempting it. As opposed to hiring a service provider to take control of a halfway-completed project, it is better to consider employing one prior to you start. Chances are you may require a professional plumber to make tube connections.
This article will certainly help you install a brand-new tub in your washroom if you have already acquired a brand-new tub and don't need to change the setup of your previous supply of water pipelines.
Your tools and also material checklist must make up the following:
Preparing for the Installation
Firstly, the sustaining framework provided with the bath must be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to ensure that if the tap comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to avoid strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of both taps making use of 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the supply of water. After doing so, turn on the taps to drain any type of water staying in the system. The process of getting rid of the existing taps can be fairly problematic because of the limited access that is usually the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the faucets. Have a towel ready for the remaining water that will certainly come from the pipes. When the supply pipelines have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from turning throughout this process. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
Before going on to fit the new taps, contrast the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Setting up the Bathtub
Utilizing the two wood boards under its feet, put the bath tub in the required placement. The wooden boards are useful in uniformly spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 tiny factors.
The next objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and also readjusting the feet on the tub up until the spirit level reads level.
To set up faucets, fit the bottom of the outermost flexible tap port to the suitable supply pipeline by making a compression sign up with; then do the same for the other tap.
Switch on the water supply and check all joints and also new pipework for leaks and tighten them if necessary. Load the bath tub and likewise inspect the overflow outlet and also the typical outlet for leakages.
Finally, take care of the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the bath tub should wait until the tub has actually been utilized a minimum of when as this will certainly settle it right into its final placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washers are in location in between the tap and also the sink. Safeguard the tap in position with the producer offered backnut. When the faucet is firmly in place, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The former kind should be connected to the tap finishes first, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to split a stiff seal, triggering the water to penetrate the wall between the bath and also the tiling, leading to difficulties with dampness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and cartridges, as well as can securing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to allow for the motion experienced when the tub remains in use. The sealant can crack relatively early if you do not take into account this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also conveniently offered on the market. It is recommended to fit the ceramic tiles using water-resistant or water resistant sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader on Installing A Bathtub, I imagined sharing that post was a good thing. Appreciated our entry? Please share it. Let other people discover it. Thank you for going through it.
Quick, quality, call! Report this page